低温磨料气射流加工PDMS实验研究

通过自研的低温磨料气射流加工装置进行低温磨料气射流加工聚二甲基硅氧烷(polydimethylsiloxane,PDMS)实验研究,分析了加工时间、加工距离、冲蚀角度和磨料粒径对冲蚀率、孔深和孔横截面形貌的影响。结果表明:随着加工时间的增加,冲蚀率先增大后减小,在第1阶段加工过程中,孔深与加工时间大致呈线性关系,增加加工时间还可使孔底部变平整;存在一个最佳加工距离使孔深最大,当加工距离大于最大加工距离时,孔深将随着加工距离的增加而急剧下降,孔的锥度随着加工距离的增大而增大;当冲蚀角度处于30°～60°之间时,冲蚀率最大,随着冲蚀角度的增加,孔的形状逐步由椭圆形变成圆形;存在一个最佳磨料粒径,使冲蚀率和孔深达到最大;当冲蚀角度小于90°时,低温磨料气射流加工PDMS材料去除机理为塑性去除和脆性去除的结合。     

氟塑料-阀芯黏结工艺

为了解决液体火箭发动机主阀阀芯氟塑料与金属黏结不良问题,对其成因与黏结工艺进行研究。采用阀芯压制氟塑料前涂覆自制聚全氟乙丙烯胶黏剂的黏结工艺方法,通过扫描电镜观察黏结面微观结构形貌并进行能谱分析,进而对涂聚全氟乙丙烯胶黏剂的黏结工艺方法进行机理分析,最后开展菌状物试样黏结工艺验证、阀芯工艺验证、工作性能试验验证。试验表明:采用涂聚2遍全氟乙丙烯胶黏剂黏结的工艺方法,可提高氟塑料和金属黏结强度,黏结强度可提高到19 MPa以上,达到未涂胶氟塑料与金属黏结强度的3倍,阀芯黏结合格率达到100%,使用性能满足使用要求,有效解决液体火箭发动机主阀阀芯黏结不良问题。     

基于通用无线电外设的北斗信号仿真系统

研究了基于通用软件无线电外设(USRP)的北斗信号仿真系统。给出了北斗卫星电文的生成方式,使用Matlab读取星历信息并定义编码产生北斗卫星信号,并利用USRP实现北斗卫星电文的调制发射,利用接收机对该信号进行捕获接收,并对信号附加的多普勒频移进行仿真。最后通过接收机对仿真系统产生的信号进行接收验证。通过此仿真系统可更直观地研究北斗卫星信号,对研究北斗卫星导航系统具有一定的参考意义。     

Advances in fabrication of ceramic corundum abrasives based on sol–gel process

Corundum abrasives with good chemical stability can be fabricated into various free abrasives and bonded abrasive tools that are widely used in the precision machining of various parts. However, these abrasives cannot satisfy the machining requirements of difficult-to-machine materials with high hardness, high strength, and strong wearing resistance. Although superhard abrasives can machine the above-mentioned materials, their dressing and manufacturing costs are high. By contrast, ceramic corundum abrasives fabricated by sol–gel method is a cost-effective product between conventional and superhard abrasives. Ceramic corundum abrasives exhibit self-sharpening and high toughness. In this review, the optimization methods of ceramic corundum abrasive properties are introduced from three aspects: precursor synthesis, particle shaping, and sintering. Firstly, the functional mechanism of seeds and additives on the microstructural and mechanical properties of abrasives is analyzed. Specifically, seeds can reduce the phase transition temperature and improve fracture toughness. The grain size and uniformly dense structure can be controlled by applying an appropriate amount of multicomponent additives. Then, the urgent need of engineering application and machinability of special shape ceramic corundum abrasives is reviewed, and three methods of abrasive shaping are summarized. The micromold replication technique is highly advanced and can be used to prepare functional abrasives. Additionally, the influence of a new sintering method, namely, two-step sintering technique, on the microstructural and mechanical performance of ceramic corundum abrasives is summarized. Finally, the challenge and developmental trend of the optimization of ceramic corundum abrasives are prospected.     

一种基于余数周期的 PRI精确估计算法

针对传统脉冲重复间隔（PRI）分选算法在估计PRI方面存在的不足，提出了一种对PRI周期信号的周期进行精确估计的算法。该算法首先从待分选脉冲序列中提取出属于一部雷达的脉冲样本，然后利用同余方程的余数周期性质对该雷达脉冲序列的PRI进行精确的估计。相对于传统的PRI估计算法，该算法有效地消除了TOA量化误差对PRI估计造成的影响，可以精确地估计出雷达脉冲序列的准确 PRI数值，从而能够更好地满足信号分选算法的处理需求。理论推导及仿真实验均表明了该算法的有效性。     

电网电压不平衡及谐波畸变时基波电压正负序分量分离新方法

针对传统锁相环(PLL)在电网电压不平衡及谐波畸变下利用常规软件锁相环不能准确获取相位的问题,提出了一种新的正负序分量分离新方法。利用了相序解耦谐振控制器能去除高次谐波和延时信号消除(DSC)法可滤除特定谐波的特性,将相序解耦谐振和延时信号消除法结合起来,达到更好的正负序分量分离的效果。最后,采用MATLAB/Simulink软件仿真结果证明了所提出方法的可行性和有效性。     

前处理工艺对航空铝锂合金硫酸阳极氧化膜层性能影响

针对一种新研制的航空用Al-Li-Cu-Zn-Mg系铝锂合金,采用了光学显微镜、电子显微镜和能谱分析技术,分析碱腐蚀和三酸脱氧两种不同前处理工艺对铝锂合金硫酸阳极氧化膜层的外观、耐蚀性和疲劳性能的影响规律。结果表明:相比三酸脱氧工艺,碱腐蚀工艺对铝锂合金表面的腐蚀程度较深,晶界处的耐腐蚀能力较差,硫酸阳极氧化膜层表面形成了网状晶界形貌;采用碱腐蚀处理的试样疲劳寿命较三酸脱氧处理试样更低,而不同前处理后经过硫酸阳极氧化的试样疲劳寿命相差不大。不同前处理对铝锂合金的硫酸阳极氧化膜层的耐蚀性的影响不大。     

ABORT-like detector to combat active deceptive jamming in a network of LFM radars

This paper studies an electronic counter-counter measures (ECCM) scheme combating against deceptive electronic counter measure (ECM) techniques.An adaptive detector exploiting generalized likelihood ratio test (GRLT) criterion is applied to detect the presence of deceptive jamming in fractional Fourier transform (FrFT) domain.First,the generating mechanism of spurious frequencies is analyzed based on the Volterra serial.The proposed nonlinear distortion model based on power amplifier behavior is robust in distortion analysis when the memory effect is considered.Second,a modified adaptive beamformer orthogonal rejection test (ABORT) like detector in closed form is built.The proposed detector can discriminate the echo and deceptive jamming adaptively by exploiting primary data and secondary data.This ECCM scheme is capable of guaranteeing the performance without the restriction of orthogonality,which is essential for the ABORT detectors.The expansion to radar network is discussed as a special case at the final part of this paper.Numerical simulations demonstrate the effectiveness of the proposed method.     

混装电路板焊接工艺设计

本文以某产品的混装电路板手工焊接为例,介绍了混装电路板焊接工艺设计的过程,包括工艺设计的依据、焊接方法的选择以及工艺设计的要点,可作为今后类似产品的设计依据和参考.     

电离层色散对DS/FH-BPSK信号解调性能影响

相位连续的DS/FH(Direct Sequence/Frequency Hopping,直接序列/跳频)扩频信号的扩频带宽比直扩信号更宽,在电离层的非线性相位以及跳频频点变化这两者的共同作用下,该信号的BPSK(Binary Phase Shift Keying,二相相移键控)解调性能明显恶化。依据随机变量概率分布的数学规律,推导得到了在背景电离层色散条件和跳频频点均匀分布前提下,某种DS/FH卫星测控信号的引导信号和长周期信号BPSK误码率的变化规律,并在特定信号参数条件下进行了误码率仿真。